Yes. The Submarine Spray Station upholds the most stringent safety standards (ASTM, EN71, ect’) and is IPX7 waterproof certified, ensuring the utmost safety in using battery-operated products when immersed in water. Still, please follow these guidelines to ensure optimal safe use of the product:

• 1. Use 4 X AA batteries only.

• 2. WARNNING: don’t use rechargeable batteries.

• 3. Use quality batteries of a known brand.

• 4. Make sure the battery compartment is tightly sealed after every time you change the batteries

Yes, this product is BPA free.

This product is recommended for children ages 2-6 years. No matter what their age, you should never leave a child unattended in the bathroom or bathtub.

Before you can start enjoying your new Submarine Spray Station, batteries must be inserted. We strongly recommend using new, good quality batteries to ensure optimal operation over time.

After inserting the batteries, close the battery compartment and attach the submarine to the bottom of the tub and the water activity station to the side of the tub with the suction cups. Make sure the water level is at least 2 inches inches (5 cm), so the water covers the submarine windows, and the activity station’s yellow propeller is at least 0.4 inches (1 cm) above the water.

4 X AA batteries (not included) of good quality and a known brand are needed. WARNNING: don’t use rechargeable batteries. Do not mix old or used and new batteries or different types of batteries.

Before inserting batteries, ensure the product is dried thoroughly!

To insert batteries, unscrew the little screw near the battery compartment cover (located on the front side – “nose” of the submarine). Than using a coin unscrew the battery compartment cover and extract the battery compartment. Insert 4 X 1.5V AA (LR6) batteries, ensuring correct polarity. Close the compartment cover and screw firmly into position.

Attention! Before putting the submarine in the water, make sure the battery compartment is tightly sealed!

After attaching the submarine to the bottom of the tub using the suction cup base, make sure the water level is at least 2 inches (5 cm), so the water covers the submarine windows, and the activity station’s yellow propeller is at least 0.4 inches (1 cm) above the water. Then just squeeze the knobs on the diver shower handle to start the water flow.

The submarine should be secured to the bottom of the bathtub, while water level must be at least 2 inches (5 cm).

Aiming the stream of water into the right funnel will spin the water gauge and spin the propeller. Directing the stream of water into the left funnel will roll the eyes and run water through the red and white water pipe. The left funnel can also be removed for fun experimentation with water flow.

Unscrew the filter (located on the bottom of the submarine under the suction cup) and pull it out. Wash with soap and water until the filter mesh is clean. Make sure the inner propeller is also clean and spins freely. Reposition the filter and screw firmly into place.

The filter should be cleaned every time batteries are replaced.

The product may stop working when the propeller or filter are blocked by dirt, hair, or soap. In order to fix this, unscrew the filter and pull it out. Wash with soap and water, ensuring that the filter mesh is completely clean. Make sure propeller rotates freely. If it does not, try to release the clog with a screwdriver until it rotates freely again. Reinsert filter and screw into place.

If you would to watch a tutorial, click here.

If the water is still not running, change the batteries and make sure to tightly close the battery compartment lid (see instructions above).

• 1. Allow the pump to fill up with water – plug the water hole on the diver showerhead with your finger/s for a minute.

• 2. Check to see if the shower head is blocked by dirt. If it is, clean it and blow air into it to clear the water exit.

• 3. Clean filter – clean mesh and make sure that the filter propeller spins freely.

• 4. Change batteries.

• 1. Check to see if the shower head is blocked by dirt. If it is, clean it and blow air into it to clear the water exit.

• 2. Verify correct polarity of batteries.

• 3. Change batteries.

• 4. Still doesn’t work? Contact us.

Check to see if the holes are blocked. If so, clean them and blow into them to release the blockage.

It is recommended to properly rinse, drain, and dry out the product after every use. Unless you do that, Yookidoo® bath toys will need a good cleaning every few weeks or so, in order to remain mold-free. When a thorough cleaning is required, fill up a bucket with water and add in some vinegar. Let the toy soak in the vinegar water for around 20 minutes, then turn it on and off a few times to circulate the water through the pump. repeat this step with clean water to wash the vinegar out. Rinse the toy off and dry using a paper or cloth towel.

The Yookidoo date code helps us track the production date of the product. The date code of the Yookidoo Submarine Spray Station is on the bottom of the submarine base. It is made up of 5-digits and ends with letters.